How the coil is attached to the trimmer. Trimmer head (coil)

The optimal choice of trimmer characteristics will not be enough for comfortable cutting of vegetation in the garden. Both for and for it is necessary to choose the right cutting tool. As such, a trimmer line (cord) or a special knife is used.

The type of vegetation is fundamental when choosing what to mow. For convenience, the user can choose the type of cord, the type of trimmer head, the method of threading the cord into it, choose a knife of a certain shape. Therefore, you should familiarize yourself with these characteristics in more detail.

TRIMMER LINE (CORD)

The classic cutting tool for all types of tools is a special trimmer line or line, also sometimes called a string. Its thickness (diameter) ranges from 1.2 to 4 mm. For each trimmer, the maximum cord thickness is indicated, which can be operated without overheating the engine and accelerated wear of the bushings.

In addition to differences in thickness, the trim cord also has a different cross-sectional shape: a circle, a polygon (from three to hexagon), an asterisk, rounded protrusions, etc. In addition, it can be twisted along the longitudinal axis in the form of a twisted square or a spiral-shaped round string, and have various notches and recesses. All these tricks are designed to increase efficiency when mowing vegetation.

The most versatile is the round cross-section trimmer line, which can be used to cut both fresh grass and dead wood. In addition to this versatile cord, manufacturers also produce more specialized line.

Taking into account that the smaller the contact area of \u200b\u200bthe cord with the stem, the greater the force of its impact, a figured cord with a cross-section in the form of a polygon or an asterisk with sharp corners appeared. Later, for strength, particles of aluminum began to be added to it.

Square fishing line with a thickness of 2.4 mm and more will allow you to easily cope with thickets of dry weeds and even stems of raspberry bushes. The sprocket, on the other hand, is designed for gentle mowing of fresh grass. Due to the profile, it cuts vegetation cleaner, the grass leaves faster after cutting and does not dry out as often as after using a round line.

Spiral-shaped round fishing line is considered low noise, but this parameter is only relevant for electric trimmers, since the sound of a running gasoline engine blocks the whistle from any fishing line.

When using a trimmer line with a figured section, its thickness should be taken less than the maximum for this trimmer - this will avoid problems with the supply of line from the mowing head. Fill such a cord into the spool with gloves.

The trimmer line comes in a variety of colors and in most cases it has no functional value. But with some manufacturers, the color determines the diameter of the cord (for example, Stihl) or the properties of the material used (for example, Oregon).

For the manufacture of trimmer lines, nylon (polyamide) or polypropylene are used. Leading manufacturers use PP6 polypropylene for cord production. Various low-quality polyethylene is often added to the fishing line of Chinese origin to reduce the cost. But in any case, after long-term storage, the polypropylene cord becomes brittle. To increase elasticity, such a fishing line should be soaked in water for half an hour before use.

Under no circumstances should thin wire or stranded wire be used as a trim cord. Thinking in this case about the strength and durability of the fishing line, they forget that the trimmer string is specially made in such a way as to break off to soften the dynamic impact on the transmission and engine of the tool. In addition, the cable and wire still break off. At the same time, broken-off pieces accelerated to high speed easily pierce leather shoes.

TRIMMER HEAD

The trimmer head, often also called the mowing head, is a specially designed reel that contains a cord of a certain length. An 8-15 m piece of cord is wound onto the inner spool, the ends of which are pulled out of the reel to the required length as they wear out or break off when they meet a too hard obstacle.

As a rule, certain mowing heads are used for different models of trimmers, which differ in both the internal structure and the way of attachment. For some trimmer heads, special adapters are available that allow these heads to be used on trimmers of various models and from different manufacturers.

Trimmer heads are usually subdivided according to the type of line feeding into manual, semi-automatic and automatic. In the first, as the name implies, the line is fed from the head manually. To do this, you will have to stop working, turn off the trimmer and manually lengthen the ends of the cord.

For the second, it is enough to hit the ground with the mowing coil. In this case, by pressing upon impact on a special button, the anchor mechanism is released and the cord is fed due to centrifugal force. Line lengthening is carried out with the trimmer working.

In the third option, to lengthen the cutting line, simply reduce the engine speed, then with a subsequent increase in speed, the trimmer line is automatically fed.

As follows from the above description, the most inconvenient is the mowing reel with manual cord feed, and the most optimal is the mowing head with automatic feed. However, it has not won much love from users due to the increased line consumption compared to other types. Therefore, the most popular and in demand today are semi-automatic trimmer heads.

Also, different models of trimmer heads differ in the way the line is threaded. They can be quick-loading (for example, Shindaiwa Speed-Feed), when there is no need to disassemble the reel to wind a new portion of the cord, and collapsible.

In the first variant, you can leave the mowing reel on the trimmer. The end of the cord is threaded through both ears in the spool, then the required amount of line is wound and cut off. Or both ends of a pre-cut piece of cord of the required length are tucked into the corresponding holes and screwed on.

In the second option, to charge a new portion of the cord, the trimmer coil will need to be removed, disassembled and wound on the spool inside. Different models of reels have different ways to disassemble and wind the line. But in all cases, the line must be wound in the direction indicated by the arrow on the body (both ends in one direction).

On cheap Chinese mowing heads, the so-called "no-name", such an arrow is often absent. Also, branded models may have two arrows in different directions (when it is possible to use them on trimmers with different directions of head rotation). In this case, the cord must be wound in the direction of rotation of the shaft (that is, the engine must wind it). If the cord is wound in the wrong direction, then when the button hits the ground, it will fly out too much.

The opposite option is also possible - when the line does not feed when the semi-automatic mowing head hits the ground. This can be caused both by improper winding of the line, or by the fact that, after installing it on the trimmer, you simply forgot to pull the ends of the cord out of the retaining grooves on the spool.

Another nuisance when mowing vegetation with a trimmer line is the sintering of the turns inside the coil. This happens because, when meeting with an obstacle that is too hard, the cord is sharply inhibited. With such jerks, it is pulled inward and sticks to the part wound on the spool. As a result, it is necessary to interrupt work, disassemble the coil and tear the stuck together turns of the cord. In some cases, this can be avoided by spraying the line wound on the spool with silicone spray before installing it into the spool.

Most often, a semi-automatic head of two spring-loaded parts (body and spool) is used for trimmers. Structurally, the spool can be in two versions. Two-section, where each end of the cord is wound into its own section, which reduces tangling and sintering. Or one-piece, when both ends of the line are wound together.

Our craftsmen came up with a simple, cheap and elegant way to turn a one-section spool into a two-section one, the essence of which can be understood from the above photos.

For this, a ring is cut out of a strong and thin plastic plate, the inner diameter of which corresponds to the thickness of the spool in the winding zone of the fishing line, and the outer diameter to the diameter to the protrusions. That is, such a ring should move freely along the spool. Then a cut is made for the cord, the ring is cut, put on the spool and the cut is glued with tape. Now each end of the line can be wound into the section intended for it.

The prewound mowing head has two or four opposed holes from which the mowing ends protrude. In addition to feed spools, there are also trimmer heads with plug-in fixed lengths (such as the Oregon Jet-FIT).

In this case, the number of working "mustaches" can be up to twelve. Some users consider such a construction to be quite convenient, but another part is unhappy, because they believe that this increases the consumption of the cord and it is necessary to stop working to replace it. In such heads, as a rule, a fishing line with transverse notches is used.

TRIMMER KNIFE

When mowing tall grass with the trim line, it will wrap around the spindle where the mowing head is attached. How often this will happen depends largely on the design of the head and the properties of the mowed grass, but it is practically impossible to completely avoid this. The optimal way out will be mowing not with a cord, but with a trimmer knife specially designed for such cases.

A trimmer knife used as a cutting tool can be made of plastic or metal and have a different number of blades (teeth) of various shapes.

On curved bar trimmer models, use only plastic blades (for the safety of the mower and commensurate with the flexibility of the flex shaft). In addition, they often come with.

This can be either a special mowing head with replaceable removable plastic knives, or a one-piece design in the form of a circular knife with a different number of blades. Tough vegetation (dry grass, burdocks, nettles, etc.) is in the teeth of such trimmer knives.

For processing large areas and mowing not only grass, but also cutting shrubs or even young trees, metal knives are used. The only thing such trimmer knives are "afraid" is collisions with objects that are too hard for them (for example, stones).

Metal knives can only be used on straight bar trimmers. They cannot be mounted on tools with a curved shaft. This is due primarily to safety technology. If, when mowing vegetation, the disc hits a solid obstacle, then it is thrown back in this case. With straight bar trimmers, the distance to the user's feet is much further.

Plus, the T (U) or J-shaped handle helps to hold the tool, and a special protruding limit bar is added to the D (O) -shaped handle, which rests on the leg does not let the cutting tool approach it. Curved bar trimmers are usually equipped with a D (O) -shaped handle without stopper.

Second, the high torque metal disc coulter puts a lot of stress on the flex shaft and motor, resulting in quick tool breakage.

As user experience shows, the shape of the blades (triangular, rectangular, etc.) has practically no effect on the quality and speed of mowing. But their quantity becomes important when using a hay trimmer. Three or four blade blades chop the grass too much when mowing.

Almost round eight-tooth knives or with four large and additional smaller teeth between them are considered the most optimal for haymaking. Perforated discs with a large number of teeth are also popular - this lightweight trimmer cutter can be installed on low-power tools.

Using a trimmer cutter, that is, a circular knife with a large number of teeth, you can not only easily clean the area from luxurious perennial weeds, raspberries, etc., but also cut trees with a trunk diameter of several centimeters.

One of the common devices for cutting grass is the trimmer. It is very easy to operate and maintain. That is why it has become popular among the population. Its significant advantage is its low weight. Even a child can handle such equipment.

What it is?

The trimmer consists of a cutting element, a bar, a motor and a handle with a control mechanism.

It is designed for mowing grass in garden areas and for creating the perfect lawn. Thanks to its compactness, the device does the necessary work in places where the mower cannot reach. In addition to grass, the trimmer is designed for mowing tree branches and bushes, as well as creating flower beds. Such equipment is not always used for lawns, as the length of the grass will have different heights.

Specifications

The main technical characteristics of the trimmer are:

• power;
• equipment weight;
• type of power supply (from the network or using a battery);
• engine location (top or bottom);
• type of cutting element;
• rod type.

All this must be taken into account when buying this or that device.

How to choose the right one?

Before purchasing this equipment, you need to understand for what purpose it will be used. For a large area with a flat lawn, it is better to purchase a light model with low power. If you need to improve the summer cottage, then you need to choose a more powerful model.

Cutting tool

To make the cutting process easy, it is necessary to choose the right cutting element.

In its role is often an ordinary trimmer line or knife. When choosing one of the species, it is worth evaluating the type of vegetation. In accordance with these data, a cord is selected, a knife of a certain shape. An important element is the trimmer head. We will consider its varieties below.

Mowing head for trimmer

It is a special assembled coil with a cord inside.

Its dimensions can be varied. A 15-meter cord should be wound on the inside of the spool. Its ends are pulled out a certain distance to do the job. When meeting with a solid object, it is destroyed. The trimmer mowing head is available in various designs. It all depends on the type of device. They differ not only in design, but also in the way they are connected. There is also a universal trimmer head that is suitable for different equipment. This was made possible by special adapters.

Kinds

The trimmer head is classified according to the line feed method:

1. Manual. In this case, the name speaks for itself, that is, the line is fed mechanically. To make the cord even longer, you must stop the trimmer and manually pull the ends.
2. Semi-automatic. If you want to replace the cord, the trimmer head needs to touch the ground. In this case, a special button is pressed and the anchor mechanism opens. Further, the cord is lengthened due to the main feature is that the procedure occurs when the trimmer is on.
3. Automatic. To make the cord elongate, the engine speed is reduced. Further, when increasing them, the line is fed automatically.

From all of the above, it follows that the manual mowing head for the trimmer is inconvenient.

That is why you should choose the automatic type. However, such a trimmer head is not popular with users, since a large amount of fishing line is consumed during operation. Therefore, the optimal view is semi-automatic.

Classification by filling method

The trimmer head can have several ways of threading the line:

1. Quick Chargers. The new cord is wound without disassembling the coil, that is, there is no need to remove it from the device. The end of the new element is pushed into the coil and then wound a certain number of times. When a specific value is reached, the cord is cut. This type of trimmer head is available from Shindaiwa and Speed-Freed.
2. Collapsible. Here the name itself speaks for itself. To replace a new line, you need to remove the spool from the equipment, then unwind the old line and wind a new one.

Design features

It should be noted that the trimmer cutter head contains special arrows. They allow you to run the coils in different directions. If it becomes necessary to wind the line in the direction of rotation of the shaft, it turns to a specific position. A large amount of wound cord can damage the equipment. The two arrows are only found on imported models. Now on the market there are heads with one arrow.

If, after hitting the semi-automatic head, the cord is not wound, then its previous winding was performed incorrectly. That is, after the trimmer head was installed, the user did not pull the ends of the line out of the grooves. Another unpleasant moment when mowing grass can be the sintering of the coil turns.

Why is this happening? This happens when the cord meets a solid object. At the same time, it sharply slows down and with the subsequent movement of the line begins to go inside the device. Thus, it falls on the spool and sticks together. Because of this, the employee has to take a break and correct the situation. However, this can be avoided. Before installing the reel, it is necessary to treat the line with a special silicone substance.

For various models of trimmers, a semi-automatic head is used, consisting of two parts - a body and a spool. Both elements contain springs. The second part can be performed in several versions:

• single-section - both parts of the line are wound together;
• two-section - each end is wound on a specific part; this type is the most effective as the line does not get tangled or baked.

There is a simple and cheap way to convert a one-piece spool to a two-piece one. This requires a sturdy plate. From it you need to cut a circle, the diameter of which should be equal to the thickness of the spool. In this case, the thickness is taken near the place where the line is wound. This circle moves freely. Next, a cut is made on the ring, put on a spool and connected with glue or tape.

As a result, you can wind the line on the required section. The head for the universal trimmer can have from two to four holes, which are located opposite each other. Mowing ends come out of them. In addition to the spools presented, there are heads where a certain size of fishing line is inserted. In this case, the number of whiskers is increased to twelve. Many users find such a device to be quite convenient. However, not all people are of this opinion.

They believe that in this situation, the line will have to be spent more. In addition, to replace it, you must stop working. The trimmer head is available in a variety of sizes and is suitable for cutting grass, shrubs and trees. Before you buy a trimmer, you need to study the terrain, as well as the features of the equipment. So, we found out what the universal trimmer head is for and how to fill it correctly.

The trimmer reel cuts the grass, but it will wear out and often need to be replaced. Recently, motorcycle or electric scythes have become widespread. The main working element of such a garden tool are spools with a fishing line tucked inside. Therefore, it is extremely important to choose a high-quality element so as not to waste finances, because the device is quite expensive. To reduce the cost of servicing brushcutters, you can learn how to independently fill the trimmer coil with wood.

Often, manufacturers of power tools do not complete their products with a number of devices that are necessary or useful for operation, offering to purchase them separately (as an additional option). With a brushcutter reel, the situation is different: since it is the main working element of a garden tool, all trimmers are supplied with it, but the quality of the reel from the scythe kit leaves much to be desired.

The consumer has to purchase the reel separately - this is done to increase sales and generate additional profit for manufacturers.

Below are questions about what a trimmer is, what coils are, and how to insert and fix the fishing line yourself.

What is a trimmer

A trimmer is understood as a brush or electric trimmer. In fact, it is a type of lawn mower (hand-held mower) that is designed for mowing grass. This is a modern braid. They were originally developed for agricultural work, but the main application of the trimmers was precisely lawn mowing.

For the first time, the idea to create a trimmer came to the mind of the American entrepreneur J. Bollas. While driving his car through an automatic car wash, he noticed that the principle of rotating brushes could be used to mow crops.

After that, he assembled a primitive trimmer from a tin can (as a spool) and a line threaded through the holes drilled in it. He installed the resulting structure on a pole, on which the engine from a moped was previously mounted. The device mowed not only wheat, but also grass. Realizing that he would earn a lot of money by selling the scythe, the entrepreneur improved his product and gave it the name "Weed killer". A feature of the invention was the ability to mow the grass around the trees - the forest cut the grass perfectly, but did not injure the bark.

The main purpose of such a tool was to mow the grass in small areas in places where classic wheeled vehicles cannot be used:

• in the presence of a large number of shrubs;
• in gardens with many trees;
• near fences and fences;
• if the site has uneven relief.

All trimmers include a barbell - the main structural element. A gasoline or electric engine is attached to the rod from one end, and a reel with a fishing line is put on the other - the main working element. In this case, the type of transmission can be any - it is limited only by the capabilities of the manufacturer and commercial parameters.

Why this tool is called differently

Trimmer was originally understood as a manual lawnmower with an electric motor. At the same time, the mower was powered both from the mains and from the battery, which can be installed on a rod or carried in a special pouch.

The main cutting element is the fishing line, which creates some restrictions on the type of processed grass: you can only mow plants with a thin and soft stem. The mowing area is limited by the length of the cable or the capacity of the battery. However, recently, braids with gasoline engines have also been called trimmers. They provide greater mobility to the worker, which can significantly increase the size of the site.

But electric and gasoline scythes were originally varieties of lawn mowers, however, with the advent of the trimmer, these designs have ceased to be in demand and are now rarely produced, and their names have passed to trimmers - most people are more accustomed to call this tool that way.

Coil specifics

In the modern world (both in the city and in the countryside), it is practically impossible to do without such a modern and useful tool as a trimmer. It is widely used by employees of public utilities in large cities, such devices are in demand in farms, they are used to improve summer cottages, vegetable gardens, orchards, etc.

Photo of the complete set of the coil of the garden trimmer.

However, it should be remembered that the main working element is the trimmer head - a spool of line. It is this element that most often fails and requires maintenance. The price of the reels has a wide range (from $ 10 to $ 150), which makes such a tool even more expensive. Any manufacturer (even a branded one) usually equips its product with an inexpensive and low-quality coil. However, it is possible to work for a rather long time with a primitive coil, subject to timely maintenance of it.

Like any other mechanical element, the coil requires cleaning of accumulated grass, cooling when overheating, and filling with lubricant. However, coils often fail for various reasons, and buying new ones or carrying broken ones for repairs is quite expensive. In this case, almost all malfunctions can be eliminated independently. It is not difficult to disassemble the coil, especially if you use the instructions.

The first part that often fails on the trimmer reel is the line. The fishing line is a consumable for which the manufacturer is not responsible. At the same time, on many models of reels, changing the line is a difficult procedure (and for some brands it is impossible). Attempting to replace the line with a material other than the original line can destroy the reel.

The coil itself (the part of the element on which the fishing line is wound) rarely fails, while the grooves through which the working part of the fishing line is threaded and which holds it can collapse (grind off), since they are almost always made of plastic.

Video about cable lubrication, shank replacement, installation of the guard and trimmer coil:

Despite the abundance of spare parts for trimmers on sale, not everyone can afford to buy them, in addition, there are often restrictions on available products. For example, manufacturers make "individual" mounts for the trimmer, a universal reel will not fit on such a mount. This often makes it impossible to obtain a suitable coil for the price. Some manufacturers make spools designed for thin line (up to 3 mm in diameter), which significantly limits the trimmer's capabilities. Therefore, there is an option to make the coil yourself.

How to make a coil yourself

The basis of a homemade reel is a disc made of durable material. It is best to use a textolite about 5 mm thick for these purposes. It is strong and reliable enough. The size of the disc depends on the size of the trimmer and personal experience - how it is more convenient to work.

Next, a hole should be drilled in the center of the disc. The hole diameter must be equal to the diameter of the rod axis (the latter is attached to the rotating shaft of the motor). In this case, it is extremely important to determine exactly the center of the disc. After that, 4 holes should be drilled for the line. Their diameter will be equal to the diameter of the fishing line, and they will be located in pairs on opposite sides of the axis (2 on one side, 2 on the other from the axis of rotation). In this case, the design of the reel is greatly simplified: it is not required to wind a large amount of fishing line, but it is enough to fix (tie) a small segment of it through the finished holes.

To give the structure the necessary strength and reliability, it is recommended to find a spring, the inner diameter of which will be equal to the diameter of the shaft, and install it on the shaft over the finished disc.

After the line is tucked in and fixed on the disc, you can start testing. The fishing line does not need to be fixed to the disc motionlessly: even when threaded through the holes, it will not fall out, because the engine gives high revolutions to the shaft, and the centrifugal force is enough to hold the fishing line under load.

This design, instead of a purchased trimmer coil, has many advantages: you can install any line (both thin and thick) into it, the device itself is practically "indestructible", and it will not take very long to purchase a new coil.

The disadvantages of this homemade product include the following:

• the need to cut a pair of pieces of fishing line of the same length;
• when installing without attaching the fishing line, it is necessary to make sure that equal lengths of fishing line hang from the reel.

Video about winding the line on the trimmer reel:

The body can be used from an old coil - it rarely breaks.

Conclusion

Such a self-made coil can significantly reduce the cost of operating the trimmer, which improves the parameters of its operation. You can use the same trimmer to cut small shrubs as well as soft and thin lawn grass.

Trimmer heads are used for cutting grass and lawns. Such a device has a fairly simple device and is easy to operate. Thanks to this, the unit has become popular with the population and utilities. Light weight is an additional plus, almost any person can cope with the work of such a device. Consider the features of the unit and manufacturer reviews.

Description

Trimmer heads include a cutting element, a special bar, a propeller and a control mechanism with a handle. The unit is intended for cutting grass in the courtyard and garden areas. The compactness of the device and ease of control allow you to do high-quality work in the most inaccessible places. With this unit, you can also prune shrubs and young gardens. Adjustable elements allow you to set the desired cutting height of grass on lawns and sites.

When choosing trim heads, pay attention to the following parameters:

• Power indicator.
• The mass of the device.
• Type of food.
• Engine placement, which can be either top or bottom.
• A type of cutting part.
• Rod type.

Classification by type of line feed

Husqvarna trimmer heads are classified according to line feed method, namely:

1. Manual type. The line is fed in this version by a mechanical method. To lengthen the cord, you will need to stop the operation of the device and pull the edges of the cutting part by hand.
2. Semiautomatic device... Such copies allow changing the cord without touching the head to the ground surface. This option is implemented using a special key and an anchor mechanism, which makes it possible to lengthen the working part of the line due to centrifugal action. It is important that the whole procedure is carried out with the unit turned on.
3. Automatic trimmer heads differ in that, during their operation, the lengthening of the cord is carried out automatically after reducing the engine speed. The line is fed in the normal mode.

Of the above mechanisms, the manual option is not very practical and convenient. Automatic variations are also not popular due to the high line consumption. The optimal version will be semi-automatic execution.

Criterias of choice

When purchasing Champion trimmer heads and other models, you need to focus on the purpose of the unit. For a large area with a flat lawn surface, it is better to use light and not very powerful modifications. If it is planned to process an overgrown summer cottage, it is more reasonable to take a model with a high power indicator.

The selection of the cutting element also plays an important role in the final functionality of the unit. The working part is a special fishing line or working knives. This takes into account the rigidity and density of the plants. The universal trimmer head will allow you to process most of the vegetation, but it does not always differ in durability and efficiency.

Device

The device in question is a special configuration reel, which is equipped with an internal cord. It can be of various sizes, it is screwed onto the inner element of the spool up to 15 meters long.

The edges of the line are set at a certain distance to allow work. If it hits solid objects (stones, trees, etc.), the working element is destroyed. Depending on the type of fixture, the heads can have different configurations. The universal analog is suitable for most modifications. This is due to the possibility of using a number of special adapters.

Threading the line

According to this parameter, trimmer heads can be divided into two categories:

1. Fast charging. On such models, when winding the cord, it is not necessary to disassemble the spool. One edge of the next tucked line is wound into a reel and wound several times. After choosing the required length, the material is cut.
2. Collapsible heads. To refuel them, you need to remove the coil from the unit, then remove the used line and wind a new analogue.

The working head contains special pointers in the form of arrows. They are responsible for the direction of movement of the working part during rotation. If it is necessary to wind the fishing line in the direction of rotation of the shaft, it is turned into a certain position. Excessive amount of cord is fraught with equipment failure.

If it is impossible to wind the cord after hitting the semi-automatic head, winding should be done again. Most likely, the user did not pull the ends of the forest out of the nests.

Popular models

Let's consider briefly the representatives of the most famous bobbin manufacturers on the domestic market:

1. Trimmer head Oleo Mac М-10 / 11.25. This model belongs to professional semi-automatic options, is used when operating a brushcutter. The diameter of the working part is 13 centimeters, it is distinguished by fast line threading.
2. "Huskvarna T-45X" - has an open eyelet, easy line feed. Work items can be changed individually. Increased reliability and reduced wear are provided by a ball bearing surface.
3. "Huskvarna T-35"... This model is an automatic line feed head (just lightly hit the reel on the ground). There is a tap and go function.
4. Champion... Modification ET 1002KA belongs to the middle price category. Differs in ease of disassembly, strong vibration is not felt during operation.
5. Trimmer head DDE. The variant of the Win 6 type is designed for mowing grass with a line with a diameter of 2-3 mm. Suitable for electric and gasoline mowers with a 10 mm working shaft. The maximum permissible speed on the shaft is 10 thousand rotations per minute.
6. Autocut С-4-2. This head is suitable for "Shtil" brushcutters, used for mowing grass and cleaning the territory. There is an automatic adjustment of the length of the working strings when the head touches the ground. Compatible with 2mm line.

Exploitation

When the cord meets solid objects, it sharply stops, as a result of which the scaffold gets inside the device. It lies under the spool and sticks together. To rectify the situation, you will need to stop work and re-lay the line. As a prevention of such inconveniences, it is recommended to treat the forest with silicone grease before installing it into the reel.

In the device of the Autocut trimmer head, as in other semi-automatic models, two parts of the main element are distinguished: the body and the spool. Spring mechanisms are provided in both parts. The spool can be run in several configurations:

• Modifications with one section. In this case, both ends of the line are wound together.
• Models with a pair of compartments. In them, each edge is wound on a specific element. This design is more efficient, avoids wood tangling and sintering.

It is quite feasible to redesign a single section spool to a dual chamber version. This will require a strong plate, from which a circle with a diameter identical to the thickness of the spool is cut. This part is in free movement. Then a cut is made on the ring, mounted on the head and fixed with tape or glue.

Features:

The universal trimmer head can be equipped with from two to four holes. They are opposite each other. Mowing ends are derived from these elements. In addition to these types of bobbins, there is a head designed for a certain size of the scaffold. In such coils, the number of whiskers increases to a dozen. Among users, opinions were divided about such devices.

Some consider such a unit to be more efficient. Others are sure that the line consumption will be significantly higher with a dubious improvement in the quality of work. In addition, the process will need to be interrupted to replace the scaffold. Consider terrain and vegetation characteristics when choosing a trimmer. After that, you can choose the option that best suits a particular situation.